[cleewindows]

my tds was 6 changed resin its now 13 please help with it,i have no water so im had it.

[cleewindows]

any ideas??

[daz1977]

run it for a few minutes, see if it drops , as some times dirt might stay in pipework/filters

[daz1977]

where do u keep ur resin,  if its damp, the resin might be shot

[Peter Fogwill]

my tds was 6 changed resin its now 13 please help with it,i have no water so im had it.

Is the DI on a small RO system?  If so have you fitted the rubber on the top of the cartridge? If not a small RO, have you got the water going in the right way, there is little arrows on top of the DI tank?

Peter

[Darranvps]

Hi

What system have you got?
Where are you based, you can always pop round to me for a few hundred litres if you are stuck.

[cleewindows]

thanks for the offer very kind.
im in cleethorpes east coast

Hi

What system have you got?
Where are you based, you can always pop round to me for a few hundred litres if you are stuck.

[cleewindows]

sorry not sure what you mean,its a small di and is a 300 gpd ro system bought from xline im gonna have a look at di now,didnt see no arrows though.

my tds was 6 changed resin its now 13 please help with it,i have no water so im had it.

Is the DI on a small RO system?  If so have you fitted the rubber on the top of the cartridge? If not a small RO, have you got the water going in the right way, there is little arrows on top of the DI tank?

Peter

[Darranvps]

thanks for the offer very kind.
im in cleethorpes east coast

Hi

What system have you got?
Where are you based, you can always pop round to me for a few hundred litres if you are stuck.

Sorry I'm in West Sussex, good luck

[cleewindows]

No worries darran,very kind of you to offer though m8!

thanks for the offer very kind.
im in cleethorpes east coast

Hi

What system have you got?
Where are you based, you can always pop round to me for a few hundred litres if you are stuck.

Sorry I'm in West Sussex, good luck

[daz1977]

where is it reading 13 after di vessel or RO

[john tomkins]

I'm with Peter on this... check you put the filled cartridges in the right way up, there is an arrow on the side thats showing up,

[cleewindows]

No worries darran,very kind of you to offer though m8!

thanks for the offer very kind.
im in cleethorpes east coast

Hi

What system have you got?
Where are you based, you can always pop round to me for a few hundred litres if you are stuck.

Sorry I'm in West Sussex, good luck

[Peter Fogwill]

sorry not sure what you mean,its a small di and is a 300 gpd ro system bought from xline im gonna have a look at di now,didnt see no arrows though.

OK it is the small RO system.  Have you got a rubber on the top of the cartridge?  If not then it needs one, or the water will be passing through the cartridge without going through the resin.

Peter

[cleewindows]

yeah i have put the rubber on top of cartridge,you mean not in the cartridge?
on top of outside of cartridge?
thats what i have done,i have tried many differnet ways and now itis tds 16
im scratching my head.
 Would it be worth taking the new resin out of the cartridge and putting some more in?
 I have the cartridge has a cross on top i pressume that means to go upwards?
 cheers for your advice

sorry not sure what you mean,its a small di and is a 300 gpd ro system bought from xline im gonna have a look at di now,didnt see no arrows though.

OK it is the small RO system.  Have you got a rubber on the top of the cartridge?  If not then it needs one, or the water will be passing through the cartridge without going through the resin.

Peter

[Peter Fogwill]

Has the cartridge got a screwed base or does it just come apart without screwing??

If it has the screw thread then where it screws is the bottom, and the rubber goes on top.

Is the cartridge held tight when the housing it tightened?  I have seen two rubbers needed to achieve this.  You can try flipping the rubber as well, although if this needs done the reading is not generally as high.

If the resin has not brought it down since your changed the resin then it won't be done. Worth a try changing it though.

What is the reading going into the DI?

Peter

[cleewindows]

there was no screwing i had to pull off,and now its loose could that be the problem??
it has 2 rubbers the cartridge seems tight when the housing is tightened!

Has the cartridge got a screwed base or does it just come apart without screwing??

If it has the screw thread then where it screws is the bottom, and the rubber goes on top.

Is the cartridge held tight when the housing it tightened?  I have seen two rubbers needed to achieve this.  You can try flipping the rubber as well, although if this needs done the reading is not generally as high.

If the resin has not brought it down since your changed the resin then it won't be done. Worth a try changing it though.

What is the reading going into the DI?

Peter

[Peter Fogwill]

I don't use this type but I think the part that comes off to fill goes to the top, instead of the other type with the screw on base that goes to the bottom.  Is this how you have it?  If not try turning it the other way.

Peter

[cleewindows]

i pulled it off that goes to top but is loose like i say,it isnt airtight should i perhaps change resin then tape it so airtight?

[Peter Fogwill]

i pulled it off that goes to top but is loose like i say,it isnt airtight should i perhaps change resin then tape it so airtight?

No it dosn't need taped, that is not your problem.  Try changing the resin though.  What is the reading going into the DI.

Peter