Interested In Advertising? | Contact Us Here
Warning!

 

Welcome to Clean It Up; the UK`s largest cleaning forum with over 34,000 members

 

Please login or register to post and reply to topics.      

 

Forgot your password? Click here

Pages: 1 [2]  All

s.w.c

  • Posts: 1174
Re: `Sticking`Fishing Pole Sections Advice
« Reply #20 on: January 18, 2009, 03:42:53 pm »
didn't take me that long , you like my half section, Ive got a couple of them they come in handy and i do like to cover base section in the heat shrink for grip.
Logged

Jeff Brimble

  • Posts: 4347
Re: `Sticking`Fishing Pole Sections Advice
« Reply #21 on: January 18, 2009, 03:57:37 pm »
Yes I do like the half section (bottom pic)  they come in v handy. Do you use the short N04 sections that come wit many fishing poles ? Do you want any tops sections ? got loads of small bits  :)
Logged

s.w.c

  • Posts: 1174
Re: `Sticking`Fishing Pole Sections Advice
« Reply #22 on: January 18, 2009, 04:09:45 pm »
im ok on top sections, but i urgently need one section though if you can help. at the top tape it needs to be able to fit into a section of 33mm and at the base it would need to be able to take my other section male joint is 35mm, this is a section i drove over reverse in my garage im stuck without it any help jeff please
Logged

Jeff Brimble

  • Posts: 4347
Re: `Sticking`Fishing Pole Sections Advice
« Reply #23 on: January 18, 2009, 04:35:44 pm »
Hey up just poked my head out the door, its cats and dogs out there !
Base section is 36 tip is 32 approx, length approx 1402 (56")  but I would need to check with some borrowed  calipers ?
Logged

s.w.c

  • Posts: 1174
Re: `Sticking`Fishing Pole Sections Advice
« Reply #24 on: January 18, 2009, 04:56:27 pm »
yea base  needs to take a section of 36 od so if you find one of your that has a od of 36 it the section that it goes into is the one i need and broke at the tip 31 or 32 is fine
Logged

s.w.c

  • Posts: 1174
Re: `Sticking`Fishing Pole Sections Advice
« Reply #25 on: January 18, 2009, 05:06:37 pm »
also its a older type of pole shimano powerloop thick walled
Logged

Jeff Brimble

  • Posts: 4347
Re: `Sticking`Fishing Pole Sections Advice
« Reply #26 on: January 18, 2009, 05:26:47 pm »
OK be in touch tomorow night.
Logged

s.w.c

  • Posts: 1174
Re: `Sticking`Fishing Pole Sections Advice
« Reply #27 on: January 18, 2009, 05:31:20 pm »
ok i would say it about the 11m section i the 12.5 an the 14
Logged

matt

Re: `Sticking`Fishing Pole Sections Advice
« Reply #28 on: January 18, 2009, 08:49:22 pm »
s.w.c, i have added your pic to the DIY forum, i trust thats ok, if not, i will remove it
Logged

s.w.c

  • Posts: 1174
Re: `Sticking`Fishing Pole Sections Advice
« Reply #29 on: January 19, 2009, 05:16:58 pm »
thats fine matt.  its just one of many smithys creations
Logged

Jeff Brimble

  • Posts: 4347
Re: `Sticking`Fishing Pole Sections Advice
« Reply #30 on: January 19, 2009, 06:28:32 pm »
Was going to take this offline to email, if anyone gets bored please ask or look away now. But it may be of benefit for anyone else trying to match sections.
Smithys I must have measured these sections 6 times each today, its close  ::) The base of the replacement must match pretty well otherwise the double thickness of the pole wrap will be of no use. If its 1mm too small the tip of your lower section will not fit.

 Could you please give me again the OD dia of the tip of the section thats going to fit into the replacement.
Then give me again the ID of the base of your original broken  section.
Same with the tip  -is there any leeway/tolerance ?
I may have a choice of two sections.
Logged

s.w.c

  • Posts: 1174
Re: `Sticking`Fishing Pole Sections Advice
« Reply #31 on: January 19, 2009, 06:54:04 pm »
ok give me half hour i got to get it out of the garage. if you email is working i will email you.
Logged

s.w.c

  • Posts: 1174
Re: `Sticking`Fishing Pole Sections Advice
« Reply #32 on: January 19, 2009, 07:52:05 pm »
check your emails jeff.
Logged
Pages: 1 [2]  All