Clean It Up
UK Window Cleaning Forum => Window Cleaning Forum => Topic started by: ֍Winp®oClean֍ on August 23, 2020, 05:14:29 pm
-
(http://www.cleanitup.co.uk/smf/1598199233_20200823_165839.jpg)(http://www.cleanitup.co.uk/smf/1598199217_20200823_170026.jpg)Here is my modified brush I spoke about on the 'best brush' thread, it works far better for me this way. The lowest (red) row of bristles are removed (cut off at base with scraper blade). I find them pretty useless and it hinders the user's view of the rest of the brush on anything above head height which is really annoying and distracting. Also, the oversized stock ends have also been removed- in standard form this really hinders the brush particularly when trying to get the bristles into corners of lower sash windows, it just limits the brush IMO. Cut them off and it's more akin to the Ultimate brush. I find I can still clean sills just as well with this brush, although I do use a swivel which helps.
Horses for courses I suppose.👍(http://www.cleanitup.co.uk/smf/1598199209_20200823_170039.jpg)(http://www.cleanitup.co.uk/smf/1598199225_20200823_170010.jpg)
-
Why didn’t you just buy a normal extreme I’ve got about 3-4 of these kicking about they look the same.
-
Why didn’t you just buy a normal extreme I’ve got about 3-4 of these kicking about they look the same.
I've got some but they're too 'Xtreme', the lack of weight doesn't make up for the negatives which that brings.
The full sill version goes too far in the wrong direction. So, I modified the brush to give the best balance of all things... according to me. The jet holes are also placed in the correct position on the sill version, unlike the standard Xtreme where they are too close to the centre.
-
Poor brush! :(
I get the obstructed vision bit. I find the cill brush better if angled slightly downward from normal. Haven’t found a good brush for sash windows yet, nothing I’ve got gets into the corners or picks the spiders nests out.
I found the stiff version very fast over the glass but too stiff for me. Good on gutters though.
-
Why didn’t you just buy a normal extreme I’ve got about 3-4 of these kicking about they look the same.
I've got some but they're too 'Xtreme', the lack of weight doesn't make up for the negatives which that brings.
The full sill version goes too far in the wrong direction. So, I modified the brush to give the best balance of all things... according to me. The jet holes are also placed in the correct position on the sill version, unlike the standard Xtreme where they are too close to the centre.
I actually like the look of your modified brush mate......might have a go at one of mine....
I find I dont use the red bristles much but they do come in handy for upper sills in tight spaces.....saves risking scratching sills....
-
like it ive been staring at 20 or so brushes from earlier days and looking at the last brush Alex sent me, I've sat there looking and going crazy but you just sparked a thought.
(http://www.cleanitup.co.uk/smf/1598199233_20200823_165839.jpg)(http://www.cleanitup.co.uk/smf/1598199217_20200823_170026.jpg)Here is my modified brush I spoke about on the 'best brush' thread, it works far better for me this way. The lowest (red) row of bristles are removed (cut off at base with scraper blade). I find them pretty useless and it hinders the user's view of the rest of the brush on anything above head height which is really annoying and distracting. Also, the oversized stock ends have also been removed- in standard form this really hinders the brush particularly when trying to get the bristles into corners of lower sash windows, it just limits the brush IMO. Cut them off and it's more akin to the Ultimate brush. I find I can still clean sills just as well with this brush, although I do use a swivel which helps.
Horses for courses I suppose.👍(http://www.cleanitup.co.uk/smf/1598199209_20200823_170039.jpg)(http://www.cleanitup.co.uk/smf/1598199225_20200823_170010.jpg)
-
My thought is to make a 5 bristle row Xtreme with a nice splay. It could still be dual trim (3 inner rows slightly shorter) or full trim. To me, this would create a more stable, usable, effective and a genuine 'every day' brush while still retaining the weight advantage. Best of both worlds.👍
-
ive cut the red bristles off one of my sill brushes too winproclean this morning....how the hell did you cut them off with a scraper blade?i used a sharp pair of scissors instead......ill try it out tomorrow....too wet and windy for working outside today!
-
ive cut the red bristles off one of my sill brushes too winproclean this morning....how the hell did you cut them off with a scraper blade?i used a sharp pair of scissors instead......ill try it out tomorrow....too wet and windy for working outside today!
Just used a new pocket scraper blade and sliced each clump off at the base, one by one. It was actually quite quick and easy. 🙂👍
-
I did something similar with an Xtreme flocked sill brush recently, only I removed both bottom rows and cut the bottom edge of the brush stock off with a jigsaw mounted in a workmate. It left me with a great everyday brush and is really good on leaded work. It’s a great scrubber on residential work, and as it has fewer bristles than say an ultimate, it doesn’t hang on to so much dirt and makes rinsing easier.
I wish Gardiner’s would put either the flocked Xtreme back into production or a DuPont TaperTec version.
-
I did something similar with an Xtreme flocked sill brush recently, only I removed both bottom rows and cut the bottom edge of the brush stock off with a jigsaw mounted in a workmate. It left me with a great everyday brush and is really good on leaded work. It’s a great scrubber on residential work, and as it has fewer bristles than say an ultimate, it doesn’t hang on to so much dirt and makes rinsing easier.
I wish Gardiner’s would put either the flocked Xtreme back into production or a DuPont TaperTec version.
I did exactly the same with my flocked Xtreme sill.🙂 However, all you end up with is a standard Xtreme with better jet positioning.
The 5 row monofilament is a better option IMO...although ideally it would be better a little softer for cold water. My next purchase will be the medium Xtreme sill and remove the lower set of bristles and stock ends from that too, as I think this will be more suited to cold water.
-
what do you think of the the close coupled jet assembly winpro?ive just added 4 of them onto a gardiner order (spare xtreme section and flocked brush)....
-
what do you think of the the close coupled jet assembly winpro?ive just added 4 of them onto a gardiner order (spare xtreme section and flocked brush)....
Really good, I prefer it. It's much neater and the tubes don't get caught on things.
This won't apply to you but it also allows the swivel to operate so much better- freely with no resistance from the jet tubes.👍
-
i actually prefer the xtreme sill brushes with the bottom row of bristles removed too...thanks winpro!this is my new favourite brush! ;)
-
i actually prefer the xtreme sill brushes with the bottom row of bristles removed too...thanks winpro!this is my new favourite brush! ;)
In the words of Del Boy.."you know it makes sense"👍
-
small tip I've used in modified brushed tools I use sonicrafter for cutting stocks and you could use it's sanding abilitys but I use dremel for sanding but it has could cutting disc but there expensive I've spend hundreds on bits for it, then a good letherman for pulling bristles out in one go. these tools make it easier and faster.
-
Next time don't cut them off. They pull out very easily with pliers (the red bits come out too), much neater job!
-
Silly question here , I ordered a load of close couples yesterday then it occurred that when I pull on the univalve it’s will tug on the T connection ?
Have you just put a straight pushfit where hose comes out of goose neck , I use swivels ?
-
Silly question here , I ordered a load of close couples yesterday then it occurred that when I pull on the univalve it’s will tug on the T connection ?
Have you just put a straight pushfit where hose comes out of goose neck , I use swivels ?
Hi P@F
If you are using a Univalve then it is important to isolate the brush head, T connectors and the jets from the effects of the hard pulling action that is used to operate the valve. Without being protected it can lead to T connector or jet failure.
The makers of the Univalve also recommend this and make a clip that does this job and sits just above the gooseneck itself. Or what many users do is to fit a 'tightly fitted' O clip to the Gooseneck hose so that it cannot pull back into the gooseneck. If doing this ensure that enough hose is above the clip to actually protect the fittings.
-
Silly question here , I ordered a load of close couples yesterday then it occurred that when I pull on the univalve it’s will tug on the T connection ?
Have you just put a straight pushfit where hose comes out of goose neck , I use swivels ?
I use 2 x small cable ties, pulled tight on the hose just as it exits the gooseneck. This acts as the 'stop' that you require. I also use Gardiner swivels.👍
-
The swivel works much better with the close coupled assembly. 👌
-
Sorry to hi-jack.
With regard to swivels which one do you find best?
Brush socket swivel, swivel adapter between standard brush socket and gooseneck socket, or gooseneck swivel?
Cheers
-
Sorry to hi-jack.
With regard to swivels which one do you find best?
Brush socket swivel, swivel adapter between standard brush socket and gooseneck socket, or gooseneck swivel?
Cheers
For me it's the 'angled' swivel which screws directly to the brush stock, then To a Quick Loq to fit plastic QL gooseneck.
-
Same as above but the straight version
-
Silly question here , I ordered a load of close couples yesterday then it occurred that when I pull on the univalve it’s will tug on the T connection ?
Have you just put a straight pushfit where hose comes out of goose neck , I use swivels ?
Hi P@F
If you are using a Univalve then it is important to isolate the brush head, T connectors and the jets from the effects of the hard pulling action that is used to operate the valve. Without being protected it can lead to T connector or jet failure.
The makers of the Univalve also recommend this and make a clip that does this job and sits just above the gooseneck itself. Or what many users do is to fit a 'tightly fitted' O clip to the Gooseneck hose so that it cannot pull back into the gooseneck. If doing this ensure that enough hose is above the clip to actually protect the fittings.
Thanks Alex , I think what I will do is put a straight pushfit and red clip where the hose leaves the goose neck , I have been doing this with a T pushfit up to now
-
Silly question here , I ordered a load of close couples yesterday then it occurred that when I pull on the univalve it’s will tug on the T connection ?
Have you just put a straight pushfit where hose comes out of goose neck , I use swivels ?
I use 2 x small cable ties, pulled tight on the hose just as it exits the gooseneck. This acts as the 'stop' that you require. I also use Gardiner swivels.👍
Do you have a pic , I can’t see how they don’t slide up with all the pulling ?
-
This is not working with my swivel type at all , the orange PU hose is also way too stiff !
If I had to angle the goose to do a velux the pipe would rise out and take away my Univalve stop ???
-
Panic over , found a way to sort of do it , tidier and a lot more clearance ;D
(http://www.cleanitup.co.uk/smf/1599238637_253DDAA3-186B-48D8-8BE1-526A99860AEC.png)
-
I'll sort you a photo out soon Rich.😄
-
Now he says ;D ;D ;D ;D
I’m just fitting up the last pole now !!!
-
(http://www.cleanitup.co.uk/smf/1599243589_20200904_191417.jpg)They will move slightly over the weeks, just nip them off and pit new ones on. They need to be tight enough to bite into the pole hose but not so tight to restrict the flow.👍
Also, all season hose is soft enough not to hinder the swivel movement at all.
(http://www.cleanitup.co.uk/smf/1599243597_20200904_191400.jpg)
-
Ahhh , I never gave the all season a thought , I have piles of it somewhere ;D
Good shout mate , have another look later :)
-
All sorted now and pretty happy to keep it this way , as the pole is tilted left the loop on the right shifts past the pivot position so it’s not in the way at all ;D
(http://www.cleanitup.co.uk/smf/1599247549_4186C704-75A3-4912-9043-B383FA6B9242.png)
-
nice soft green tubing do you use it all the way through the pole, I've been using soft green 6mm tubing through my poles for years,
-
Just modified my 3 , got a standard Xtreme delivered on Friday which I used today , god I’ve missed that brush , at 105 gram it’s a winner but although Alex has now machined it to take pods he’s left the holes in the same too close places , why I wonder ?
So I took the pliers and band sander to the Xtreme sills I have and got them down from 138 to 115 grams !