[Plankton]

Not slating the Gardiner slx as it's all I used, however I'm sick of replacing sections 1-3 and most of the clamps regularly on someone's else's pole.
Never him that broke it, doesn't know how it happened etc
So how long should an employee expect to get out of an slx 25, how often should shims and levers be replaced.
I wouldn't expect someone to use cheap and heavy equipment and I think the clx would wear down even quicker as this is what I found over ten years ago.

[Tam1872]

For an employee id looking which is the most ridgit, not the most lightest.

An employee isn't looking after it, I'm not saying they will intentionally break it, but when  its not coming out there pocket when it needs replacing then it's unlikely they will care that much.

[Scottish Cleaning Service]

That's the reason I don't employ too many pitfalls.

[AuRavelling79]

Not slating the Gardiner slx as it's all I used, however I'm sick of replacing sections 1-3 and most of the clamps regularly on someone's else's pole.
Never him that broke it, doesn't know how it happened etc
So how long should an employee expect to get out of an slx 25, how often should shims and levers be replaced.
I wouldn't expect someone to use cheap and heavy equipment and I think the clx would wear down even quicker as this is what I found over ten years ago.

Typically how long does it last before he breaks a section?

[Plankton]

It's been 3 sections at once when I've discovered it while checking the shims, that's happened twice and other times it's single sections. Clamps cranked up to feck, shims obliterated before you know it.
I'll tape up pole near clamp fit new shims, adjust clamps, explain about this and that....
1st year it was about 6 months with 3 sections shreded, then about 2 issues the next year and the next, and been a couple of single sections this year.

[colin bird]

Three section Harris decorators pole attach brush on top,tape pole hose to pole happy days ,

[Splash and dash]

It's been 3 sections at once when I've discovered it while checking the shims, that's happened twice and other times it's single sections. Clamps cranked up to feck, shims obliterated before you know it.
I'll tape up pole near clamp fit new shims, adjust clamps, explain about this and that....
1st year it was about 6 months with 3 sections shreded, then about 2 issues the next year and the next, and been a couple of single sections this year.

Sounds like abuse of your equipment to me we replace slx every 3 years or so don’t usually replace any part of the pole , I would be having a quite word with the guy and saying any further damage and it will be coming out of his wages

[Plankton]

Splash, I said this before to him that I wasn't putting my hand in my pocket for anymore sections. He coughed up towards it before but just wears everything out so quickly.
I started with an old bendy Bayersan years ago and quickly went to Gardiners so I  appreciate how hard the job is with poor equipment, I'm also reluctant to buy from particular suppliers.
I had a pole for years which had clamp upgrades, lacquer etc as it was my pride and joy  but trying to get an average of what others are getting out of them.

[Splash and dash]

Splash, I said this before to him that I wasn't putting my hand in my pocket for anymore sections. He coughed up towards it before but just wears everything out so quickly.
I started with an old bendy Bayersan years ago and quickly went to Gardiners so I  appreciate how hard the job is with poor equipment, I'm also reluctant to buy from particular suppliers.
I had a pole for years which had clamp upgrades, lacquer etc as it was my pride and joy  but trying to get an average of what others are getting out of them.

I have 5 guys working for  me and don’t have any issues like this , I certainly wouldn’t tolerate abuse of kit like  that , accidents do happen and that’s fine but someone regularly doing that to poles would either be paying for  it or up the road

[Slacky]

You’re assuming it’s abuse. If you expect an employee to start paying out of his own pocket for wear and tear you’re gonna be looking for new employees.

How can you expect an employee to pay for equipment? They’re not an employee by definition if that’s what’s happening.

[Slacky]

and it will be coming out of his wages

That’s theft.