Interested In Advertising? | Contact Us Here
Warning!

 

Welcome to Clean It Up; the UK`s largest cleaning forum with over 34,000 members

 

Please login or register to post and reply to topics.      

 

Forgot your password? Click here

Pages: [1]

peekeclean

  • Posts: 348
what flow rate do you use?
« on: July 27, 2008, 05:48:52 pm »
what flow rate do you use and what style do you use brush on or off??
Logged

Frank pole

  • Posts: 143
Re: what flow rate do you use?
« Reply #1 on: July 27, 2008, 06:42:27 pm »
Dont know what the flow rate is but I knock the flow master up to about 5 ish - does a decent job and dont waste the pure water!
Logged

peekeclean

  • Posts: 348
Re: what flow rate do you use?
« Reply #2 on: July 27, 2008, 08:02:38 pm »
your flow rate is how much water you use a min
mine is 1and a half lt a min.
Logged

NWH

  • Posts: 16952
Re: what flow rate do you use?
« Reply #3 on: July 27, 2008, 08:14:15 pm »
The flow rate you use is all about the look and feel you get when working,you just know when your using either to much or to little.If your having to chase water down the glass over and over your not using enough.
Logged

L.J.Thorpe

  • Posts: 2056
Re: what flow rate do you use?
« Reply #4 on: July 27, 2008, 08:54:33 pm »
between 1.5 and 2 lpm depending
Logged

Alex Gardiner

  • Posts: 7744
Re: what flow rate do you use?
« Reply #5 on: July 27, 2008, 09:03:20 pm »
1.7-2.00 - brush off.
Logged

peter holley

Re: what flow rate do you use?
« Reply #6 on: July 27, 2008, 09:18:07 pm »
WATER GUSHING DOWN THE WINDOW (sorry didnt mean to SHOUT)i find that i work faster this way, and dont use much more water....tomorrow im going to buy peter fogwills autobrush....
Logged

Pj

Re: what flow rate do you use?
« Reply #7 on: July 27, 2008, 09:26:46 pm »
Turn up the flow and go man go!

Thankfully water is still cheaper than fuel!  In fact it is our fuel!  Not a drop wasted, all back into the natural cycle.

I might put that on my van....Powered by Water...What do you think?
Logged

peter holley

Re: what flow rate do you use?
« Reply #8 on: July 27, 2008, 09:48:51 pm »
your nuts ;D ;D ;D ha ha ;D
Logged

pjulk

Re: what flow rate do you use?
« Reply #9 on: July 27, 2008, 09:56:25 pm »
I could not say what flow rate but 60psi flojet 100mtrs of minibore hose and full flow.

I tilt the brush on the glass to rinse
Logged

alanwilson

  • Posts: 1885
Re: what flow rate do you use?
« Reply #10 on: July 27, 2008, 10:39:02 pm »
probably about 2.5 - 3.0ltrs a min.
Logged
I've never been to bed with an ugly bird but I've woken up with loads!

Nathanael Jones

  • Posts: 5596
Re: what flow rate do you use?
« Reply #11 on: July 27, 2008, 10:46:08 pm »
I never understood the "I use less water than you" mentality,.... It's not a competition!!!

Personally I've tried to reduce my water usage simply so I can work all day without refilling, but I find the job goes slower if I go below 1 litre a minute,.. and normally my flow is nearly 2 lpm.
Logged

[GQC] Tim

  • Posts: 4536
Re: what flow rate do you use?
« Reply #12 on: July 27, 2008, 11:26:44 pm »
Wfp goes so slow with a low flowrate, atleast 1.6lmp, 2lpm on first cleans. Brush on rinsing for tops.
Logged

craig jwc

  • Posts: 1076
Re: what flow rate do you use?
« Reply #13 on: July 28, 2008, 09:23:12 am »
Can't remember what the flow rate is but have Varistream set at 12 0'clock position when working on own.
Use 100m 6mm microbore with Vikan brush on pole.
Usually rince brush off unless working above 1st floor.
I don't change Varistream position if on 1st clean as i find this position good for all jobs.
Logged

gary999

  • Posts: 8156
Re: what flow rate do you use?
« Reply #14 on: July 28, 2008, 04:57:12 pm »
setting just past one on my flowmaster
Logged

Frank pole

  • Posts: 143
Re: what flow rate do you use?
« Reply #15 on: July 28, 2008, 05:02:01 pm »
what pump does your flowmaster operate? - I set to 5 ish with a shurflo 100 psi
Logged

gary999

  • Posts: 8156
Re: what flow rate do you use?
« Reply #16 on: July 28, 2008, 07:56:56 pm »
same 100 psi 50 mtr microbore and 1.5mm jets in my brushes
Logged

Wayne Thomas

Re: what flow rate do you use?
« Reply #17 on: July 28, 2008, 08:03:13 pm »
2+ on
Logged

Oakley Windows

Re: what flow rate do you use?
« Reply #18 on: July 28, 2008, 08:09:41 pm »
Quote from: Frank pole on July 28, 2008, 05:02:01 pm
what pump does your flowmaster operate? - I set to 5 ish with a shurflo 100 psi

Same here
Logged
Pages: [1]