Interested In Advertising? | Contact Us Here
Warning!

 

Welcome to Clean It Up; the UK`s largest cleaning forum with over 34,000 members

 

Please login or register to post and reply to topics.      

 

Forgot your password? Click here

Dynafoam

Re: cleaning carpet tiles
« Reply #20 on: October 06, 2004, 11:20:37 am »
Ian,

The only way to increase airflow with your existing machine (without modification is with wand technique.

Paul has mentioned lowering the wand to induce airflow at the front lip on the second dry pass, but remembering that not only the quantity but the proportion of water recovered diminishes rapidly in a few seconds after application I feel this not to be the best approach.

By raising the handle slightly whilst spraying airflow is increased at the jet-side lip, inducing a flow of the injected water horizontally through the surface fibres, enhancing both water recovery and flushing action. As soon as the wand has passed a section of carpet any remaining water starts its' downward journey into the lower structure of the carpet.

Now, with the first dry pass, the requirement is to raise water from deeper in the carpets' structure. The proportion of water (complete with any additional soil collected) that is recoverable is necessarily reduced but to maximise this proportion, water lift, rather than airflow becomes the prime concern so a foreword push stroke with both lips seated is best.

On a very dirty tile or glue-down it is now worthwhile to to a further, quick, wet pass using the wand at the angle of the first pass, to flush this raised soil. Subsequent dry passes then use high airflow at the leading lip.

The Recoil does not come with a vented wand. I am sure that as a cleaner/designer with a passion for the industry and more interested in improvements to the available equipment than simple pushing out machines, Ed did consider wand-venting. My own views on that topic could fill a length post but for now I will confine myself to simply saying that a vented wand is always vented in the same way, whereas the venting of a non-vented wand is in the control of the operator and subject to his/her wand skills.

The 'gadget' Eds' machine has is the total design concept - AO all the way.

jacko

  • Posts: 304
Re: cleaning carpet tiles
« Reply #21 on: October 26, 2004, 10:07:51 pm »
Hello Guys

Did this job today and went fine. Agitated well, and 3 drying passes of wand. Tiles were dry within 30 mins (and there was very little ventilation as the top of a big Church) I used my air mover to good effect. Job took 10 hours. Only hassle was removing lots of gum (but made easier by Solutions Chewing Gum Remover) - thanks Nick - excellant product.!

buyhostmachines

  • Posts: 14
Re: cleaning carpet tiles
« Reply #22 on: October 30, 2004, 05:51:13 am »
There are several problems of cleaning carpet titles with the wet cleaning methods.

#1.  A lot of carpet tiles are on computer raised floors where electrical wires run underneath.  If water makes it's way underneath sub-tile-floor and gets into the electrical, there can be more than just damage to the carpet tiles.

#2. Carpet tiles are glued down. To much moisture along with hot water will be more than enough to cause the adhesive to loosen and thus carpet tiles can not only come up from the the sub-tile-floor, but the adhesives that actually hold the carpet tiles together.  In otherwords, you have adhesive between the floor and the tile and adhesive between the fibers and the backing.  It's almost a guarantee that if you wet clean carpet tiles you're going to have problems.  I hate to be blunt, but that's the truth of the matter.

#3. Yellowing and browning are very common problems with traditional wet cleaning in general, but on carpet tiles is even more-so.

#4. The system that I have been using over 20 years is called the Host Dry Extraction Carpet Cleaning Method.  Host is a moist granule cellulose sponges that have the similar principal as your kitchen counter top sponge.  Those cellulose granule sponges are very capable of loosing, trapping and absorbing dirt and grime without leaving the carpets sopping wet, uneven, dull, or even watermarks.  Those problems aren't a problem with Host.  Carpets are usually able to be put back into use immediately after cleaning (no down time).  You won't have any problems with all of the above listed, and no water marks, browning, delimitation, etc.  And best of all, you don't have to worry about putting any protectors back underneath your furniture after cleaning. Very little furniture needs to be moved anyway, and no water will travel under the carpet to get existing furniture wet.  This system is a true time-saver and can even be used to clean Sisal products.  Wet cleaning is strictly discouraged by the manufactures who make them.  Most of those manufactures will tell you to "Host Dry Clean Only."  I have been cleaning with Host for over 20 years, belong to the HPCA and have had personal experience in cleaning carpet titles in a building I use to work in.  That was a 24 communications building in which the workers would either only have their break time or either stand aside from their desk while I cleaned their carpet tiles.  Then they were back working  immediately after cleaning.   

If you would like a Host Dry Extraction Carpet Cleaning professional  in your area, simply leave your post with all your contact information (email, city, state and country) and I'll be happy to forward it onto you.

I hope all this information helps.
Charles

HolmansUKLTD

  • Posts: 849
Re: cleaning carpet tiles
« Reply #23 on: October 30, 2004, 06:48:51 am »
I use cahrly pads on tiles seems to work fine most of the time and dries within 20-30mins

Nick
Surreys No1 Carpet & Upholstery cleaner
Surreys No1 Dart player
IICRC water restoration Technician

cleanmac

  • Posts: 104
Re: cleaning carpet tiles
« Reply #24 on: October 31, 2004, 12:08:35 am »
Charles,it is dirty capettiles we speaking about not clean ones,of course on the latter Host truly excels.

David