Clean It Up

UK Window Cleaning Forum => Window Cleaning Forum => Topic started by: Blue Frog Systems on September 06, 2009, 09:52:47 pm

Title: Quick Q for Alex Gardiner
Post by: Blue Frog Systems on September 06, 2009, 09:52:47 pm
Am converting a harris pole and was wondering which one of these will fit a harris pole ? If you dont know is there any chance of a diameter measurement and i can check myself at B&Q with one of there own tape to save me taking mine  ;D

Plastic Taper Pole-end Screw Type1

Plastic Taper Pole-end Screw Type2

Will be ordering a brush & bits on tue and thought if i dont get any freebies off bentley i should get one from you with my order.

Tanks in advance Mr G  :D
Title: Re: Quick Q for Alex Gardiner
Post by: Alex Gardiner on September 06, 2009, 09:59:36 pm
I doubt if you'll get any freebies off Bentley as they do not keep these screw ends in stock.  They are made in China complete with the handle and brush and sent over in complete boxes.  Our local Asda sells the Bentley brushes so they are out there still.

Type 1 = 19.5mm
Type 2 = 18mm
Title: Re: Quick Q for Alex Gardiner
Post by: Blue Frog Systems on September 06, 2009, 10:32:52 pm
Mr G, your are fountain of your own knowledge. I have no clue how that will sound to anyone else, but it sounds right to me.

While your about im going to carry on with the Q's .....

Im going to be ordering a The Super-Lite® Brush Dual-Trim Flocked Bristles. Now it says it comes with pencil jets as standard. Now how would i go about getting fan jets in the brush rather than the old pencils ? and whats the price difference in it for your time or someone elses time + your Little take?

Tanks
Title: Re: Quick Q for Alex Gardiner
Post by: jouk45 on September 06, 2009, 10:41:10 pm
alex, i was comparing price on carbon poles on your  site, and am a bit confuse, 24ft xt-l carbon pole including vat £500 an sl-x 25ft carbon pole £368 including and i thought the sl-x was going to be more expensive, i just never thought the xtel would have been that price, is this correct
Title: Re: Quick Q for Alex Gardiner
Post by: jouk45 on September 06, 2009, 10:45:31 pm
window wipers, i tried the bentley pole adaptor for my harris pole, and found it did not fit slightly small, i pasted it in 2 part epoxy, then inserted it, then put a screw in there,
Title: Re: Quick Q for Alex Gardiner
Post by: Alex Gardiner on September 07, 2009, 07:23:40 am
alex, i was comparing price on carbon poles on your  site, and am a bit confuse, 24ft xt-l carbon pole including vat £500 an sl-x 25ft carbon pole £368 including and i thought the sl-x was going to be more expensive, i just never thought the xtel would have been that price, is this correct

Whilst the SL-X range is a premium pole, it is still good value.  Even if they weren't the lightest and most compact range in the world (which they are) they would still be good value.
Title: Re: Quick Q for Alex Gardiner
Post by: Alex Gardiner on September 07, 2009, 07:25:08 am
Quote from: Window Wipers link=topic=80549.msg708937#msg708937

Im going to be ordering a The Super-Lite® Brush Dual-Trim Flocked Bristles. Now it says it comes with pencil jets as standard. Now how would i go about getting fan jets in the brush rather than the old pencils ? and whats the price difference in it for your time or someone elses time + your Little take?

Thanks

The only way of doing this is to ring the Office (01726 66400) and they will be able to tell you the price difference and get it arranged.
Title: Re: Quick Q for Alex Gardiner
Post by: jonnyald on September 07, 2009, 08:04:52 am
i noticed that in my B AND Q  some of the vileda or addis range of floor mops on a pole had  the screw ends that you mention.these were cheap
Title: Re: Quick Q for Alex Gardiner
Post by: Blue Frog Systems on September 07, 2009, 09:19:32 am
Thanks Alex :)