Clean It Up
UK Window Cleaning Forum => Window Cleaning Forum => Topic started by: sunshine windows on March 13, 2008, 03:36:54 pm
-
Hi guys,
As some of you are probably aware, I scratched a few of my customer's sills last month with the head of the brush.
I've been round them all today and sorted out the problem, with the help of a few pieces of advice from the forum.
Can't remember who metioned it but I got myself some 2000 grade wet and dry off ebay and it worked a treat.
Just wanted to relay the info to anyone else who might come across this problem in the future.
Thanks once again to whoever suggested the wet and dry solution.
Lance
-
Your welcome ;) and it does work a treat doesn't it? might also pay you to next time run a little polish over the sills after useing the wet and dry.
-
Hi Jeff,
Thought it might have been you.
Yes it does work a treat. Even some very deep gouges came out with the wet and dry.
I should have charged them for a restoration clean this time round. ;D
Once again thanks for your advice mate.
Lance
-
Anyone come across those really rough mitered corners yet where it looks like the upvc was smoothed off with an angle grinder?
-
No problem Lance, ;)
I had a few houses with loads of bad scratches, (all on a builders cleans) lucky for me the plastc surgeon was on site, when I asked him the best way to remove them, he then told me about the wet & Dry, I thought to myself, this guy's taken the P but he came out with me and showed me how remove the scratches, I was amazed when he had finished the sills looked like new again.
I should have known better, because in my caravan manual, it shows you how to remove scratches from the plastic windows useing wet & dry.
I had a job with marks that the custy couldn't remove from a frame and sill, were they removed that creeping Ivy and it left all its little sucker marks, I did the Job when the custy was out, and when they returned they phoned to say how pleased they were, they added a £20 tip to my bill.
Was your Custy happy with the Job?????
And for those who read this, restoring the frames and sills can be a good little earner.
-
All 4 of the customer's who's sills I scratched had their windows cleaned and sills buffed up by the wet and dry today. Every one of them happy as Larry, so hopefully no lost revenue there.
Lance
-
I have come across a few new jobs where the ends of the sills are rough as A*****es. Like you said DJW it looks like a right botch job.
Lance
-
Jeff What do you use to polish the pvc with after rubbing down? Just the usual cream cleaner?
Wayne
-
You can use a little car polish, makes them shine a treat and gives them a little more protection.
-
The brushes we are using are scratching the sills ive had a customer cancel today and he mentioned the sills were scratched but his main reason for cancelling is that his windows were left wet, he said he thought we dried them off.
I explained about wfp he said he was going to get a window cleaner that uses ladders for a 3 storey house so then i explained about health & safety and that he would be in trouble if an accident occured, thats when he started complaining about the scratches on his sills that was the only bit of sense he made
so the suppliers need to come up with a good brush that doesnt scratch sills
Brett
-
This will stop the scratched sills, a bit heavy but may help you.
-
Brett what brush are you using? I have had problems with sills recently with an old type Ionics? would also like to add thanks for sharing the info with us lance I have been taking on a lot of new cleans recently and have noticed in some cases scratches on the sills ::)
-
Personally I wouldn't think it was the bristles on the brush scratching the sill, more to do with the brush stock scrapping along the sill which is easily done.
The Vikan sill brush is very handy but a little on the heavy side for work above 18ft if yo need to work say over Cons or flat roofs.
@Jeff, Thanks for the tip Jeff
Wayne
-
Thanks Jeff
seen those brushes before thought they might be a bit heavy
chris, im using a vikan rectangle but ive also complaints with my ionics one as well, did you recieve my email a few days ago
Brett.
-
Brett is your Ionics a dual crinkle brush or the new Ionics Dual Trim (None Crinkle)
Cheers
Wayne
-
Brett is your Ionics a dual crinkle brush or the new Ionics Dual Trim (None Crinkle)
Cheers
Wayne
Hi wayne
my ionics is a commercial brush just normal nylon bristles but you are right its definately not the bristles its the brush stock scratching the sills
Brett.
-
I use the vikan sill brush.
Have done now for nearly 2 years as i was getting complaints of scratched sills.
Now no complaints and the sills come up excellent.
I don't think there too heavy but i was using a 16" vikan before.
I have other poles with vikan brushes and also double trim brush and a yellow one which i think was from WCW but i prefer the vikan sill brush.
Paul
-
I take it with the wet and dry you need to keep it really wet to get the scratch out and not put any new one's in.
Paul
-
With my ionics the bristles are soft and the jets protrude about 3-4 mm from the bottom of the brush its either this scratching the sill or the edge of the brush not sure yet, however the new stiffer Ionics combined with a Gaz mk2 swivel as far as I'm concerned is the mutts.
Brett sorry just found it reply in the post ;)
-
I think the marks left on sills are mostly 'scuff' marks from the stock, there will be scratches of course, particularly if the stock on the brush has got a little rough and now has a few embedded particles of grit.
For actual scratches I think the tip of wet & dry is a really good one...gonna get myself a few sheets so I'm prepared ;)
Anyone tried T-cut? I guess it won't remove actual scratches, but I'd be interested to see if it would remove more general scuff marks.
It's one of the negatives of WFP, you can mark up sills and you can also chip paintwork :-\
Ian
-
ive used "T" cut in past to remove the black marks left on the patio door steps when ive cleaned along the bottom of the doors and caught the step with the edge of the vikan brush. Used to get red marks when i used the ovals.I try to be more careful now. Wet n dry sounds a far better idea though.Thanks all for your tips. Syd
-
I take it with the wet and dry you need to keep it really wet to get the scratch out and not put any new one's in.
Paul
Just keep it nice and wet Paul and all will be fine.
-
So how does this work then? Wet the sill and then rub along the sill?
-
So how does this work then? Wet the sill and then rub along the sill?
Yes thats the correct way, do not go across the sill, keep the paper and the sill wet.
-
So how does this work then? Wet the sill and then rub along the sill?
Yes thats the correct way, do not go across the sill, keep the paper and the sill wet.
So after getting paint off (WD40?) you could use the paper to get rid of the "staining".
-
I have removed artex staining on a couple of frames useing this method, so I'm sure it will work with paint stains, you won't do any damage by trying.
If the above fails, come back on here and I will give you a tip that will remove it.
-
I have removed artex staining on a couple of frames useing this method, so I'm sure it will work with paint stains, you won't do any damage by trying.
If the above fails, come back on here and I will give you a tip that will remove it.
Will try on my own first, had a few people askin me about it.
-
Don't worry jonathan, I tried it out on my own first ;D I had one bad sill on the outside toilet, used the wet'n'dry and it brought it up like new.
-
Don't worry jonathan, I tried it out on my own first ;D I had one bad sill on the outside toilet, used the wet'n'dry and it brought it up like new.
Mine have got burns from nitromores on it (I buggered up a few years ago) so hopefully that should work. I suppose what it does is take a little layer of PVC off?
-
I was looking at some sanding sponges in B&Q the other day - was tempted to try them but forgot all about it.
-
Don't worry jonathan, I tried it out on my own first ;D I had one bad sill on the outside toilet, used the wet'n'dry and it brought it up like new.
Mine have got burns from nitromores on it (I buggered up a few years ago) so hopefully that should work. I suppose what it does is take a little layer of PVC off?
I can't see it being a huge difference, this same method is used for removing scratches from plastic caravan windows, its also used for restoring scratched CD's why pay £10 for a machine that does it for you, when for a couple of bob you can restore your own, (use a figure 8 pattern and try it on an old CD)
I was looking at some sanding sponges in B&Q the other day - was tempted to try them but forgot all about it.
Dave, arn't they a little bit rough, I don't think there 2000 grade.
-
There was a really fine one from jml or someone looked like the sponge they use for packaging almost. It was being sold as a magic stain remover but i reckon it was just slightly abraisive.
-
There was a really fine one from jml or someone looked like the sponge they use for packaging almost. It was being sold as a magic stain remover but i reckon it was just slightly abraisive.
If its cheaper than wet'n'dry, then buy one and give it a try, but try it on your own sills first.
But don't come back and say I told you to buy one ;D ;D ;D ;D ;D ;)
-
What about getting highbuild off sills. Highbuild is a textured masonary paint.
-
What about getting highbuild off sills. Highbuild is a textured masonary paint.
That was one of my original problems, I scraped it off and left a couple of scratches because it was hard to scape off, try and use a strong plastic scraper at first, then use your W&D.