Clean It Up
UK Window Cleaning Forum => Window Cleaning Forum => Topic started by: Dean Aspects on February 29, 2008, 11:46:54 am
-
I check my di resin at the beginning of the week but this week i forgot so checked it yesterday 012 but no one has phoned and complained so maybe i have got away with it
Dean
-
Dean
Several people (myself included) have posted on here saying that they have cleaned with various TDS readings going up as high as 20 ppm.
In my short experience I have found that once it leaves 0 ppm it goes up higher quite rapidly (I only have a small Di unit).
I have also found that you are more likely to 'get away with it' where the rinse water 'curtains' down the glass and less likely to 'get away with it' where the water 'beads' on the glass.
I'm looking to get bigger Di units as a result.
Regards
Mike
-
What brand of resin do you both use?
tony
-
Purolite near the end of the bag when its finished going to try tulsion from DA services
Dean
-
Purolite near the end of the bag when its finished going to try tulsion from DA services
Dean
Good move, have you changed the resin already dean? did you shake the vessel?
tony
-
Yes shook the vessel and it made no difference changed the resin yesterday
By the time i got home checked tds again it was at 35ppm my tap water was at 25ppm so it started to make the water worse
All sorted now though
Dean
-
Yes shook the vessel and it made no difference changed the resin yesterday
By the time i got home checked tds again it was at 35ppm my tap water was at 25ppm so it started to make the water worse
All sorted now though
Dean
Typical with purolite, you should have better luck with tulsion. I was the same with purolite, as soon as it hit 001ppm it would shoot right up within a day. i use dowex now, when mine hits 001ppm it'll stay there for a week then very slowley start rising. then i shake the vessel & it's back to 000ppm for a while.
Tony
-
I went out with tds reading of over 200 once. GULP !!!!!!
-
Does shaking the vessel make a difference then?
Mine is at 001 and has been for a couple of weeks. Still deciding which resin to buy and where from. Last lot was from RO-Man. It soes not say which type it is on the side!
-
Mate of mine plumbed his RO up wrong in the beggining went out with tap water,he lost loads and loads of work and couldn`t work out why for about a week.
-
Does shaking the vessel make a difference then?
Mine is at 001 and has been for a couple of weeks. Still deciding which resin to buy and where from. Last lot was from RO-Man. It soes not say which type it is on the side!
Let some water out to make room inside, cap inlet/outlet off with loop of hose or thumbs & shake the whole vessel up/down side to side to mix the resin up inside for about a minute. leave to stand for 5 mins, run a few litres through it & you should be back to 000ppm. ;)
Tony
-
The minute my tds goes above 000 I change it. But I only have a really small di vessel so no probs for me.
Steve
-
macmac and myself do it differently, we both use 2 di vessels inline. Saves a small fortune on resin as you can use resin til it is completely spent.
-
macmac and myself do it differently, we both use 2 di vessels inline. Saves a small fortune on resin as you can use resin til it is completely spent.
;) ;) ;) ;) ;) ;) ;)
-
you see......great minds.
thats all I gotta say......great minds
-
it would be a great idea if there was a small inlinebattery tds meter with an alarm on it, this way we would be warned when the tds got to 1ppm.
found this one http://www.tdsmeter.co.uk/products/pm1.html
-
What's the best resin to use. I've always used Rohm & Haas but can't find it on the websites.
-
What's the best resin to use. I've always used Rohm & Haas but can't find it on the websites.
From my experience it's dowex, although tulsion (DA SERVICES) is also sposed to be good. Get mine from wintecs with free delivery.
Tony
-
What's the best resin to use. I've always used Rohm & Haas but can't find it on the websites.
From my experience it's dowex, although tulsion (DA SERVICES) is also sposed to be good. Get mine from wintecs with free delivery.
Tony
Tony,
Is Dowex & Tulsion virgin resin?
-
What's the best resin to use. I've always used Rohm & Haas but can't find it on the websites.
From my experience it's dowex, although tulsion (DA SERVICES) is also sposed to be good. Get mine from wintecs with free delivery.
Tony
Tony,
Is Dowex & Tulsion virgin resin?
Yes mate, are you DI only, or RO-DI?
Tony
-
RO. I haven't bought a bag of resin in over a year now. I'm down to half a bag so thinking of getting some more now.
-
RO. I haven't bought a bag of resin in over a year now. I'm down to half a bag so thinking of getting some more now.
Yeah, the quality of resin doesn't have as much importance when only using such a small amount. with your circumstances i would be happy to use any brand.
Tony
-
Just done a bit of calculating there.
Resin 1 - Input 007ppm
Output - 003ppm
this is after putting over 36000ltrs through it.
vessel is 5ltr
thats dowex for you.