Clean It Up

UK Floor Cleaning Forum => Carpet Cleaning Forum => Topic started by: Dave_Lee on September 16, 2004, 08:28:27 pm

Title: Burst Solution Line.
Post by: Dave_Lee on September 16, 2004, 08:28:27 pm

Hi All,
One of those days today. Cleaning a newly decorated babys bedroom this afternoon, only cleaned a square metre after having pre sprayed whole carpet - suddenly burst solution line close to shut off valve. Water everywhere, up the walls door and out on the landing and up the landing mirror. big wet patch on bedroom carpet. Fortunatly client staying out of the way downstairs. Big wipe down with clean Terries, vac up excess from carpet - lift carpet and check underlay - wet, vac underlay, swop sol line and finish cleaning carpet, then leave blower blowing underneath the carpet while I do the stairs - dry underlay and carpet backing by the time I m packed away, then resecure carpet.
Took my solution line to fluid and hydraulic engineers place in Preston expecting them to be able to fix on a new end screwed piece, but they wouldnt do it as their insurance doesnt cover repairs in case it was to blow under the pressure. Looks like its a waste of an otherwise good solution line and Ill have to get a new one, unless anyone out there knows different?
Dave.

Title: Re: Burst Solution Line.
Post by: adl on September 16, 2004, 08:45:22 pm

Dave there is a company on heaton street in leyland 2nd on left up golden hill lane called P & N Neumatics they do all my repairs they also sell male and female connectors for solution lines.

regards dave adl

Title: Re: Burst Solution Line.
Post by: adl on September 16, 2004, 08:47:03 pm

Dave
PS  if you are short of a solution line untill you get yours fixed i have 4 X 50ft sections spare at moment give me a call you can borrow with pleasure

regards dave adl

Title: Re: Burst Solution Line.
Post by: Big_Fish on September 16, 2004, 08:58:43 pm

A&M Cleaning Supplies
01923 671587
have a very good repair/parts centre, 'phone them first, may be worth the transport costs to get it there.

BFN

Title: Re: Burst Solution Line.
Post by: eclipse on September 16, 2004, 09:28:17 pm

Funny that I  had the same thing happen to me yesterday only difference was i was using a v2 steam mate at the time as luck would have it i had just put wand down to go turn machine off when it went
took hose to a local hydraulics company where they presure tested hose and crimped me the old end back on it cost a grand total of 5 pounds (made me a bit wary about using the steam mate on full now though as hose popped where the wand would have been near my thigh ouch!! :o

Title: Re: Burst Solution Line.
Post by: Phil Marlor on September 16, 2004, 10:09:37 pm

Dave,

A company called Pirtek Hose & Assemblies.

There is one in Preston, tel: no. is 01772 620111.

They can crimp new ends or replace solution hose and quick connectors.

If anyone wants their nearest branch just phone 0800 382438 this will put you directly to the branch nearest to you.

Web site is www.pirtek.co.uk

Had 5 new ends crimped last week at the Luton branch, cost just £30.00

Phil

Title: Re: Burst Solution Line.
Post by: mark_roberts on September 16, 2004, 10:30:31 pm

I remember the first time this happened to me.  Only in the business a few months and so I flapped big time and without thinking ran down the stairs to turn off the machine instead of putting the solution line into the vac hose!!!

Water everywhere and the customer was standing talking to me at the time.

Put it down to experience.

Mark

Title: Re: Burst Solution Line.
Post by: Doug Holloway on September 16, 2004, 10:38:28 pm

Hi Guys,

I've had this so many times in past 2 years (twice today) but as I'm only working at 100psi its not generally too catastropic.

Cheers,

Doug

Title: Re: Burst Solution Line.
Post by: Dave_Lee on September 17, 2004, 02:41:45 am

Thanks to all for your replies, and especially telephone numbers and company details where I can get the line repaired.
Thanks also Dave for your offer of loan of hose, much appreciatted.
Dave.