Clean It Up

UK Window Cleaning Forum => Window Cleaning Forum => Topic started by: Clear Vision on September 26, 2006, 07:18:03 pm

Title: How do you fit these jets to a brush?
Post by: Clear Vision on September 26, 2006, 07:18:03 pm

I just got one of gaz's brushes and a couple of cleantech's push fit fan jets.

How on earth do I fit them ???

What other fittings will I need?

What size of pipe will I need?

I am going to fit the brush to a 2.4m pole (2 section) What piping will I need?

Cheers

Matthew

Title: Re: How do you fit these jets to a brush?
Post by: matt on September 26, 2006, 07:55:26 pm

i did a guide to building a brush

its on the DIY site

http://www.d.co.uk/brush/

Title: Re: How do you fit these jets to a brush?
Post by: Clear Vision on September 26, 2006, 10:46:26 pm

Thanks matt. thats great ;)

Where can I get the bulkhead connectors from?

Matthew

Title: Re: How do you fit these jets to a brush?
Post by: chris@c.m.s on September 26, 2006, 11:16:29 pm

Mathew what pole are you hoping to put your brush onto?
 

Title: Re: How do you fit these jets to a brush?
Post by: matt on September 27, 2006, 08:39:02 am

Quote from: Clear Vision on September 26, 2006, 10:46:26 pm

Thanks matt. thats great ;)

Where can I get the bulkhead connectors from?

Matthew

cleantech, only a few quid

Title: Re: How do you fit these jets to a brush?
Post by: JM123 on September 29, 2006, 12:42:38 am

esiest way is to drill 2 8mm holes and push them through with the hose on them from the bristle side  - nice tight fit and takes 2 mins

Title: Re: How do you fit these jets to a brush?
Post by: s.hughes on September 29, 2006, 08:35:30 am

I dont think that jet needs a bulkhead connector. I could be wrong but cleantech do 2 types of them jets and one needs them the other dont

steve

Title: Re: How do you fit these jets to a brush?
Post by: matt on September 29, 2006, 10:18:11 am

Quote from: How Much????? on September 29, 2006, 08:35:30 am

I dont think that jet needs a bulkhead connector. I could be wrong but cleantech do 2 types of them jets and one needs them the other dont

steve

the jet is in the pic next to the brush, and its the type that needs the bulkhead connection

Title: Re: How do you fit these jets to a brush?
Post by: JM123 on September 29, 2006, 06:48:57 pm

here's how its done - NO bulkhead required.

sorry for the poor picture quality but I had to use the phone to take the pics

Title: Re: How do you fit these jets to a brush?
Post by: Jeff Brimble on September 29, 2006, 06:50:34 pm

You got woodworm in that brush too  ;D

Title: Re: How do you fit these jets to a brush?
Post by: JM123 on September 29, 2006, 07:00:21 pm

No actually its ventilation holes as I work so fast I need to ventilate the brush to stop it overheating.

Title: Re: How do you fit these jets to a brush?
Post by: Jeff Brimble on September 29, 2006, 07:15:27 pm

That will be a new topic then
 "Help what removes friction burns off glass ? "

Title: Re: How do you fit these jets to a brush?
Post by: JM123 on September 29, 2006, 07:43:17 pm

 ;D ;D ;D ;D ;D ;D

gg4!!