Clean It Up
UK General Cleaning Forum => General Cleaning Forum => Topic started by: MarkSutcliffe on April 02, 2017, 07:51:47 pm
-
I've bought one second hand of eBay, quite a decent price..
Set it up with a buffer tank to test it, and there is no pressure from the gun..
Pressure coming out of the machine is quite high, but then nothing from the gun...
any suggestions as the vario lance seems to be a sealed unit,
thanks
-
When you say pressure coming from the machine, do you mean water is coming out?
If water is coming out then you may need to remove the lance from the high pressure hose then fire up the machine again and this time let it run for a minute without the lance to let the system prime - You should notice the pressure kick in - Stop the machine and reintroduce the lance.
-
Didn't you test it before purchase ?
-
I've no idea what washer you have but I thought most of those Clarke washers were direct feed.
Anyhow if it is defo the type of washer that sucks from a buffer tank you will need to start the washer on full throttle with the choke on first with your lance trigger pulled in. Turning the choke off when it starts. To prime the pump just lower the throttle still with the lance trigger pulled in until it the pump builds up pressure. In doing so water will start to flow out of the lance. Then just throttle up and away you go.
-
I've bought one second hand of eBay, quite a decent price..
Set it up with a buffer tank to test it, and there is no pressure from the gun..
Pressure coming out of the machine is quite high, but then nothing from the gun...
any suggestions as the vario lance seems to be a sealed unit,
thanks
Mark did you manage to get it working ok?
-
Hello, I've not yet thanks.. I'm going to try it again in the morning, i'm 90% certain its the lance..
but there is a jetwash repair place nearby and they told me today to just take it down and they'll have a look, rather than selling me a lance which might not be needed..
I'm going to try and get a normal lance which I can change the ends rather than a variable lance..
-
So with no hose on it jets out the pump? If you connect the hose but no lance it jets out of the hose.
Have you removed the jet to see if it's blocked?
If you are getting pressure out of the pump you need to work along the supply chain until you find the blockage
-
Took it to the jetmac who are based down the road..
Lad there took one look and diagnosed it in seconds... piece of rusty metal clogging up the sprayer... Got it out with a piece of guitar string..
-
I've no idea what washer you have but I thought most of those Clarke washers were direct feed.
Anyhow if it is defo the type of washer that sucks from a buffer tank you will need to start the washer on full throttle with the choke on first with your lance trigger pulled in. Turning the choke off when it starts. To prime the pump just lower the throttle still with the lance trigger pulled in until it the pump builds up pressure. In doing so water will start to flow out of the lance. Then just throttle up and away you go.
no pressure on the buffer tank feed, bought through eBay so im covered :)
tried your instructions and it didn't work, when i syphoned some through it pulled its own, but nowhere near enough,..
-
Have you tried it connected directly to an outside tap instead as I'm not convinced it will work from a buffer tank?
-
Talk to the legend Lee Kenny, he has loads of second hand machines, and only person I trust with p washers
Phone number is 07871 242012 .
Tell him Tony Soprano sent you
-
Talk to the legend Lee Kenny, he has loads of second hand machines, and only person I trust with p washers
Phone number is 07871 242012 .
Tell him Tony Soprano sent you
Hmmmm! Have you ever tried Ben at Rutland Pumps? He deffo knows his onions when it comes to PW's
-
right ok,
clarke pls265
runs off the supplied feed (you were right smurf)
wont pull from buffer tank.. should be able to, but wont...
gun is knackered though, needle point sprays, no other setting works.
-
right ok,
clarke pls265
runs off the supplied feed (you were right smurf)
wont pull from buffer tank.. should be able to, but wont...
gun is knackered though, needle point sprays, no other setting works.
Time you spent messing about you could have bought a decent machine and be hitting peak drive cleaning season !
-
Talk to the legend Lee Kenny, he has loads of second hand machines, and only person I trust with p washers
Phone number is 07871 242012 .
Tell him Tony Soprano sent you
Hmmmm! Have you ever tried Ben at Rutland Pumps? He deffo knows his onions when it comes to PW's
Lee kenny is the best no doubt, was trained by the countries top pump pro's !
-
Talk to the legend Lee Kenny, he has loads of second hand machines, and only person I trust with p washers
Phone number is 07871 242012 .
Tell him Tony Soprano sent you
Hmmmm! Have you ever tried Ben at Rutland Pumps? He deffo knows his onions when it comes to PW's
You stick to tiling ;D
-
Who is this Lee Kenny chap as in what is his trading name and does he have a website?
-
Who is this Lee Kenny chap as in what is his trading name and does he have a website?
https://powerwashcleaning.co.uk/contact-us
-
Talk to the legend Lee Kenny, he has loads of second hand machines, and only person I trust with p washers
Phone number is 07871 242012 .
Tell him Tony Soprano sent you
Hmmmm! Have you ever tried Ben at Rutland Pumps? He deffo knows his onions when it comes to PW's
You stick to tiling ;D
Oh! OK Mr Sugar I will try :o
-
Talk to the legend Lee Kenny, he has loads of second hand machines, and only person I trust with p washers
Phone number is 07871 242012 .
Tell him Tony Soprano sent you
Hmmmm! Have you ever tried Ben at Rutland Pumps? He deffo knows his onions when it comes to PW's
You stick to tiling ;D
Oh! OK Mr Sugar I will try :o
Ireally like you Kev, you have given me some excellent advice in the past. Was only joking honest
Love you x
-
So was I ! You don't really believe I was comparing you to a successful Billionaire and Knight of the Realm do you?