Clean It Up

UK Floor Cleaning Forum => Carpet Cleaning Forum => Topic started by: Dave Roelants on November 26, 2011, 05:15:38 pm

Title: Blower to waste tank connection
Post by: Dave Roelants on November 26, 2011, 05:15:38 pm
The flexible hose that connect the blower to the waste tank on my TM is nearing the end of it's life as I think it was probably cut too short to start with.

I'm having trouble finding a 3in. 76mm. hose that will withstand the vacuum and it occured to me plastic solvent weld pipe would be a better alternative with smoother airflow,anybody tried this? Anybody have a hose supplier who has the flexible stuff if I can't source the plastic stuff?
Title: Re: Blower to waste tank connection
Post by: Paul Moss on November 26, 2011, 07:00:40 pm
Try Hydramaster  :D
Title: Re: Blower to waste tank connection
Post by: Dave Roelants on November 26, 2011, 07:30:37 pm
My names Roelants Paul not Rothschild ;)
Title: Re: Blower to waste tank connection
Post by: Simon Gerrard on November 26, 2011, 07:35:20 pm
Dave,
You could try these, they seem to stock a wide variety of pipes and fittings.
http://www.hyphose.com/index.php?main_page=products_all

Simon
Title: Re: Blower to waste tank connection
Post by: The Carpet Cleaning Pro on November 27, 2011, 04:19:52 pm
Would you kindly let me know if you track some down Dave as having the same problem.
Title: Re: Blower to waste tank connection
Post by: Tony Gill Carpet Smart on November 27, 2011, 11:56:18 pm
Dave its marine wet exhaust hose must be wire reinforced
Something like in the link below Cheers Tony

http://www.ebay.co.uk/itm/3-76mm-Marine-Wet-Exhaust-Hose-/160681068367?pt=UK_CarsParts_Vehicles_BoatEquipment_Accessories_SM&hash=item256956874f
Title: Re: Blower to waste tank connection
Post by: Dave Roelants on November 28, 2011, 05:53:23 pm
No good on my setup Tony I'm afraid, it's just not flexible enough to fit where it needs to but thanks anyway.
Title: Re: Blower to waste tank connection
Post by: elliott cleaning on November 28, 2011, 08:48:23 pm
Reckon your always going to be between a rock and a hard place on this one, Dave.
Flexibility is always going to have to be compromised on the strength required for a 4 series blower
Title: Re: Blower to waste tank connection
Post by: Mike Halliday on November 28, 2011, 09:01:33 pm
I use a 56 blower and use 2.5 vacuum hose it does not need to be exceptionally strong, after all it only take the same power as the vacuum hose leading to the wand.

you can (almost)  use any hose that fits

I also use  drainage, plastic 90 degree elbows to aim the hose at the waste tank
Title: Re: Blower to waste tank connection
Post by: Dave Roelants on November 28, 2011, 09:15:54 pm
Mike I've had 2 lots from Pirtek, both reinforced with a steel coil, the first collapsed inwards restricting the flow, the secnd retracted all it's coils like a snake and then kinked! 2.5in is the biggest normal carpet cleaning vac hose in this country but I need 3in for my setup so what I'm going to do is use 2 90deg s/s elbows giving me an almost straight run and join them with marine exhaust hose
Title: Re: Blower to waste tank connection
Post by: Mike Halliday on November 28, 2011, 09:29:24 pm
Dave how can it possible crush steel coil reinforced hose but not normal T/M hose? they both handle exactly the same implosive power, unless it was at a very tight bend.

bit of a radical idea but if it is a straight run then why does it need to be flexible.... use 3 inch fallpipe!!
Title: Re: Blower to waste tank connection
Post by: Paul Moss on November 28, 2011, 09:42:54 pm
If its almost a striaght run and you need a small bend then this may help

http://www.ebay.co.uk/itm/EXHAUST-FLEXI-PIPE-S-S-FLEXIPIPE-3-INCH-100x76MM-/290601499876?pt=UK_CarsParts_Vehicles_CarParts_SM&hash=item43a932fce4

They do other stuff too.
Title: Re: Blower to waste tank connection
Post by: Shaun_Ashmore on November 28, 2011, 09:48:03 pm
Dave I use these in Sheffield,

http://www.leplahydraulics.co.uk/products

The website isn't up to date but worth a phone call.

Shaun