Clean It Up

UK Window Cleaning Forum => Window Cleaning Forum => Topic started by: dave.e on August 27, 2011, 08:45:13 pm

Title: new brush
Post by: dave.e on August 27, 2011, 08:45:13 pm

Hi guys have any of you used one of the new 4 jetted brushes from cleaning spot it looks like a fab idea having the benefit of 2 fan jets and 2 pencil jet just wounded what they are like cheers Dave

http://www.cleaningspot.co.uk/acatalog/water_fed_pole_Double_Trim_Brushes.html

Title: Re: new brush
Post by: Pope vader on August 27, 2011, 08:51:47 pm

i got one of them, and you cant use all 4 at same time as there isnt enough pressure,  but that might just be my system,   the brush is good brush, bit stiff  i find it good on first cleans

Title: Re: new brush
Post by: ♠Winp®oClean♠ on August 27, 2011, 08:52:39 pm

I tried one of those (but with two jets)

They aren't ultralight as it says & to be honest I found it rubbish, binned it after a very short while!

Rock hard stock with cruel edges & very stiff bristles!

Title: Re: new brush
Post by: dave.e on August 27, 2011, 09:05:26 pm

thanks guys i wanted to start fitting more jets and looked at them because it would save me converting all mine. i did one today a super lite with 3x1mm jets the only problem i am having is getting the dam hole straight will have to look at something else or buy a pillar drill.

Title: Re: new brush
Post by: Slash on August 28, 2011, 02:46:36 pm

I use these brushes and think they are good,lighter than the vikan ovals I've been using,they have amazing scrubbing power and I do think they are good brushes as they have double trim bristles that get into all the little nooks and crannies and you can change from pencil to fan depending on the glass sheeting or not!
The only downfall is that they do tend to bend a little but not much,after a few weeks of use the edges of the platform bows out slightly from where the pressure has been forced on the stock piece but can be forced back into shape manually,other than that I think they are good brushes :D

Title: Re: new brush
Post by: dave.e on August 28, 2011, 02:47:56 pm

thanks slash

Title: Re: new brush
Post by: Alex Gardiner on August 28, 2011, 04:35:37 pm

Quote from: Dave@S2none on August 27, 2011, 09:05:26 pm

thanks guys i wanted to start fitting more jets and looked at them because it would save me converting all mine. i did one today a super lite with 3x1mm jets the only problem i am having is getting the dam hole straight will have to look at something else or buy a pillar drill.

Most suppliers will have full workshop facilities with pillar drills etc. I am sure that if you ring your favourite supplier up and ask for an extra hole or two to be put in a brush stock they would be able to do this for a small fee.  :)

Title: Re: new brush
Post by: dave.e on August 28, 2011, 04:58:54 pm

Quote from: Alex Gardiner on August 28, 2011, 04:35:37 pm

Quote from: Dave@S2none on August 27, 2011, 09:05:26 pm

thanks guys i wanted to start fitting more jets and looked at them because it would save me converting all mine. i did one today a super lite with 3x1mm jets the only problem i am having is getting the dam hole straight will have to look at something else or buy a pillar drill.

Most suppliers will have full workshop facilities with pillar drills etc. I am sure that if you ring your favourite supplier up and ask for an extra hole or two to be put in a brush stock they would be able to do this for a small fee.  :)

thanks alex i will email you next week with the size of the holes i wanted and thanks again for replying
 dave

Title: Re: new brush
Post by: Scrimble on August 28, 2011, 08:21:33 pm

i have one of them which i use for conny roof cleans, good for scrubing