Clean It Up
UK Window Cleaning Forum => Window Cleaning Forum => Topic started by: Stephen burton on August 08, 2019, 10:23:53 pm
-
I have a Gardiner slx 25, it’s about 2 years old, it’s starting to twist and spin more frequently is it time to buy a new one or can it be repaired cheap enough before buying a new one?
-
just clamp it up an inch or 2 and tighten the clamp up a bit....if its still spinning id just buy a new one.....
-
is it spinning in the closed position (where each section is at its shortest) - if so, open up the section and run your thumb nail from the clamp towards the next section have you got a step/ridge about 1" away from the clamp ?
if so heat the clamp gently to release the glue and pull off clamp - cut off about 1.5 inches (40mm) from the end of the section and re-glue clamp - this should sort it - I use a 1mm wide grinding disc
if it spins in various positions you may need new shims in the clamp lever assembly
Darran
-
Same here, getting to the point where I need to sort it out. At the shortest point, about an inch from the clap is worn so I'll be taping it off and spraying a couple of coats of lacquer, dry In-between and should be ok.
-
Alex did a video a while back showing how to build up the worn section with epoxy resin. I've done it several times, it's easy. It might be on Gardiner's website.
-
I'll have a look, suppose it would be a lot harder waring.
-
Try this great find.
I didn't even prep my clx pole first just alcohol wiped it.
We've been using it for 2 months & smashing it every day.
Sometimes the poles scrape along gutters & tbh there are places where chips & scrapes are coming off.
Next time I would do better prep & maybe an under coat.
But that pole was unusable before because of wear & it's a great maintenance thing to save clamp wear etc.
https://www.holden.co.uk/p/step_3_kbs_rustseal_silver_us_8_oz_
-
Get a can of clear lacquer for car bodywork and build it up using coats of it instead of faffing around with epox resin.. Cheap as chips and does a fantastic job, one of the best things you can do to maintain your pole and the lacquer also provides a grippy surface which seems to need less tightening of the clamps.
There's a guy on YouTube with a video of him doing it which is where I came across it. Search for lgb window cleaning, I think that's his channel.
-
Get a can of clear lacquer for car bodywork and build it up using coats of it instead of faffing around with epox resin.. Cheap as chips and does a fantastic job, one of the best things you can do to maintain your pole and the lacquer also provides a grippy surface which seems to need less tightening of the clamps.
There's a guy on YouTube with a video of him doing it which is where I came across it. Search for lgb window cleaning, I think that's his channel.
I tried that on a carbon slx. Made a right mess. Started flaking & went stick & gooey un the heat. Took me ages to clean it all off again. I guess you’re talking fibreglass?
I would replace the shim & spring. If that doesn’t work then as said above paint or spread a thin film of epoxy glue round the affected part. Epoxy two part glue is only £1 in a shop where I live.
Worked for me.
-
Get a can of clear lacquer for car bodywork and build it up using coats of it instead of faffing around with epox resin.. Cheap as chips and does a fantastic job, one of the best things you can do to maintain your pole and the lacquer also provides a grippy surface which seems to need less tightening of the clamps.
There's a guy on YouTube with a video of him doing it which is where I came across it. Search for lgb window cleaning, I think that's his channel.
I tried that on a carbon slx. Made a right mess. Started flaking & went stick & gooey un the heat. Took me ages to clean it all off again. I guess you’re talking fibreglass?
I would replace the shim & spring. If that doesn’t work then as said above paint or spread a thin film of epoxy glue round the affected part. Epoxy two part glue is only £1 in a shop where I live.
Worked for me.
Simon, I have an slx25 and haven't had any of those issues at all, I just build it up with thin layers letting it dry fully before adding another until happy.
Outside of regular cleaning it's the number one thing I do to maintain my poles and I wish I'd known about it a long time ago.
-
My xtreme was spinning after 9-10 months, replaced the clamps with phantom last month and they’ve been mega, so much better than gardiner clamps and you won’t have carbon hand too!
-
Get a can of clear lacquer for car bodywork and build it up using coats of it instead of faffing around with epox resin.. Cheap as chips and does a fantastic job, one of the best things you can do to maintain your pole and the lacquer also provides a grippy surface which seems to need less tightening of the clamps.
There's a guy on YouTube with a video of him doing it which is where I came across it. Search for lgb window cleaning, I think that's his channel.
Yep thats me,
https://www.youtube.com/watch?v=RDbXLzjpIjI
If anyone is experiencing problems with the lacquer then it's not be done correctly. We have an extreme 1 from 2011 and its still like new!
-
Just buy an oval 8 from streamline,problem solved.
-
I used the 2 part araldite, it's a bit time consuming but it worked well.
If it happens again, i'll just cut the section off and re-glue the clamp.
-
is it spinning in the closed position (where each section is at its shortest) - if so, open up the section and run your thumb nail from the clamp towards the next section have you got a step/ridge about 1" away from the clamp ?
if so heat the clamp gently to release the glue and pull off clamp - cut off about 1.5 inches (40mm) from the end of the section and re-glue clamp - this should sort it - I use a 1mm wide grinding disc
if it spins in various positions you may need new shims in the clamp lever assembly
Darran
Great stuff!
Are you using a hot air gun to heat it?