Pages: [1]

Dave Parry

  • Posts: 411
Ashbys external Steam mate
« on: December 19, 2003, 01:52:38 am »
There was a post recently about ashbys steam mate where I said that I was very happy with mine. Should have known better, as now it's started blowing fuses. :-X  Since I do not fancy a trip to Dartford, or having to pack it up and send it, tried to take it apart, and lo and behold it has a security type screw holding it together. Has anybody any idea where I can obtain a key for same ? I'm sure that it's probably a wiring fault, but can't prove it until I can get inside. Also it annoys me that I own a piece of kit, but can't service it myself.  ??? ???
Logged
Bracknell, Berkshire,
Phoenix T/M,
http://www.cleanercarpets.org/index.html

ALEXDH

Re: Ashbys external Steam mate
« Reply #1 on: December 19, 2003, 02:12:41 am »
is it like a star looking allen bolt.

Computer shops do them i think ,

or you can just about misuse a screwdriver pushing down hard.

same thing in xboxes.
Logged

CATMAN

  • Posts: 217
Re: Ashbys external Steam mate
« Reply #2 on: December 19, 2003, 08:46:47 am »
DAVE,

You can get a full box of different drives including this one from screwfix for £10.

http://www.screwfix.com/app/sfd/cat/pro.jsp?ts=16013&id=18983

You will also need to dry everything out, I have done away with red on/off switch as it fills with water, and replace most of the wiring, preferrably with much thicker stuff. If you check the wiring some of it will of split.

Catman.

Ps. I don't know how these machines got onto the market, good idea, just unrealiable.
Logged

Alex

  • Posts: 232
Re: Ashbys external Steam mate
« Reply #3 on: December 19, 2003, 02:23:34 pm »
Dave,

I guessing you're not to happy to say the lease about not serviceing your machine yourself, but just make sure there that you test the machine correctly as you don't want any problems if it's not serviced correct and you're onsite.

I may have just wrote a load of rubbish but best to be safe than sorry.

Hope you get sorted.

Alex
Logged

Dave Parry

  • Posts: 411
Re: Ashbys external Steam mate
« Reply #4 on: December 19, 2003, 06:41:36 pm »
Thanks all for replies, specially catman, the screw looks like a star drive but has a bit sticking up in the middle (so needs a star with a hole in the middle). Looks like there are some in this kit, so have ordered it. will post outcome when fixed (or binned). :D :D
Logged
Bracknell, Berkshire,
Phoenix T/M,
http://www.cleanercarpets.org/index.html

Kinver_Clean

  • Posts: 1120
Re: Ashbys external Steam mate
« Reply #5 on: December 19, 2003, 06:50:17 pm »
If you have a star drive and it has not got a hole, use a small strong screwdriver to break the pip off.
Maplins have all sorts of goodies and connectors etc.
Trevor
Logged
God must love stupid people---He made so many.

Ian Gourlay

  • Posts: 5748
Re: Ashbys external Steam mate
« Reply #6 on: December 19, 2003, 11:51:30 pm »
My internal one was blowing trip switches. It turned out to be damp as I was keeping equipment in a cold place.

Try keeping it inside over the weekend, if you dont do so already.


Regards

Ian
Logged

Cloverleaf

Re: Ashbys external Steam mate
« Reply #7 on: December 20, 2003, 12:55:40 am »
I,v binned my steam mate with same problem, damp inside due to leaks.
Ashbys told me heat exchanger and heater welded together and they charged me £25 to look at it :o as I declined the repair!  
Logged
Pages: [1]